Land Pride RC3620
Double tap to zoom
|All Land Pride Cutters have been designed and tested and meet rigorous voluntary
|Factory assembled||Saves customer set-up time and money. Adjustments should always be made by dealer.|
|250 HP divider gearbox
130 HP center & wing gearboxes
|A rugged heavy-built gearboxes capable of handling heavy-cutting applications.|
|Gearbox Seal Protection||Gearbox bottom seal protection for longer bearing life.|
|2" Output gearbox shaft||Large output shaft handles shock loads better.|
Cat. 6 CV or Cat. 5 Conventional
|Holds up to shock loads and harsh mowing conditions.|
|Easy Greasable drivelines||Drivelines have access holes for greasing the U-joints and to grease the inner profiles.|
|2 or 4 Plate slip-clutch||Protects drivelines and gearboxes by slipping clutches rather than twisting the driveline
when impacts are encountered.
|High blade tip speed||Allows clean cutting of material & even distribution. See Specifications for actual FPM.|
|6" Blade overlap||Eliminates skipping during turns.|
|Good cutting capacity||Can cut brushy areas with saplings up to 2".|
|13" Deck height||Handles heavy cutting, which reduces balling-up of cut material under the deck.|
|10 Ga. stump jumper backed with a
1" x 4 1/2" thick blade mounting bar
|Heavy round stump jumper for protecting the gearbox seal and gearbox output shaft.
Can hold up to tough conditions.
|Spindle Nut Protected||Spindle nut and threads extending beyond the nut are guarded to protect against
damage from hitting solid objects.
|10 gauge smooth deck top||Reduces accumulation of debris and is easier and faster to clean.|
|1/4" side skirt||Reduces debris piercing possibilities.|
|Self-leveling hitch||Reduces drawbar wear by keeping hitch level while going through ditches.|
|Hinged wing sections||Allows cutter to follow terrain. Ideal for rough ground where hillsides, ditches, and
hollows can cause uneven cutting.
|1" Solid hinge rods||Larger diameter hinge gives greater strength to cutter and hinge area.|
|Wing transport locks||Holds transport wings in the folded-up position in case of hydraulic pressure loss.|
|Enclosed front to rear dual leveling
|Dual leveling rods enable the cutter to pull equally on the rear axle during travel over
rough terrain. Many competitors only use one leveling rod.
|5-Bolt hubs||5-Bolt hubs makes the wheel assembly more durable and longer lasting.|
|Drain holes in wheel rims||Allows water to drain from wheels mounted on folded-up wings.
Helps prevent paint deterioration and rusting to the wheel rims.
|Spring-cushioned center axle||Protects unit from bumps and ground shock, cushions loads on drawbar.|
|Replaceable wheel spindles||Wheel spindles can be replaced when damaged without replacing the entire axle.
Simply remove one bolt to replace damaged spindle.
|Rephasing lift cylinders||Allows cutter to be leveled using hydraulic cylinders verse mechanical turnbuckles.|
|7/8" Leveling rods||Large diameter leveling rods provide superior supporting strength over rough terrain.|
|Double swivel hitch option||Great for uneven terrain, reduces drawbar wear. Must use spacer washers on drawbar.|
|LP Performance Hitch option||Great for uneven terrain, reduces drawbar wear. Hitch pivots freely up and down and pivots about the tractor drawbar.|
|Bar-tite hitch option||Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear.|
|LED Signal lights||LED lights are bright, long lasting, and resistant to vibration, unlike incandescent counterparts.|
|Wheel options||Laminated tires: Eliminates flats.
Airplane tires without foam filling: Give better cushion while transporting.
Airplane tires with foam filling: Give better cushion while transporting & can’t go flat.
|Deck rings (optional)||Keeps blades from damaging the deck.|
|Specifications & Capacities||RC3620 & RCM3620|
|Tractor horsepower||70 hp (52.2 kw) to 160 hp (119.3 kw)|
|Gearbox Horsepower||250 hp (186.4 kw) Splitter
130 hp (96.9 kw) Center & Wing
|Gearbox Oil Capacity||5.18 Pints (2.45 L): Divider Gearbox
6.76 Pints (3.20 L): Center deck, LH deck & RH deck spindle gearboxes
|Gearbox Lubrication||Gear Lube 80-90W EP|
|Cutting Capacity||2" (5.1 cm)|
|Weights Total Machine
|6,680 lbs. (3030 kg) (Front & Rear Single Chain guards, 6 AC tires, CV Driveline, & standard
|Blade Tip Speed
16,000 FPM (81.3 mps)
16,500 FPM (83.8 mps)
|Hitch Types||Optional Self-Leveling Clevis Hitch, LP Performance Hitch,
Bar-Tite Hitch, Pintle Hitch, or Ball Hitch
|Hitch Jack||Standard 7,000 lbs. (3,175 kg)|
|Signal Lights 7 Pin connector||LED
SAE J5560 pin configuration
Minimum Transport Width
|20' - 0" (6.10 m)
20' - 10" (6.35 m)
9' - 11" (3.02 m) (With cutting height at 2")
|Overall Length||17' - 6" (5.33 m) (With cutting height at 2")|
|Deck Height||13" (33 cm)|
|Cutting Height*||2" to 12" (5.1 cm to 30.5 cm)|
3 1/4" x 8" Rephasing hydraulic cylinder with hoses, fittings & stroke control spacers.
3" x 8" Rephasing hydraulic cylinder with hoses & fittings.
2 3/4" x 8" Rephasing hydraulic cylinder with hoses & fittings.
|Wing Folding Hydraulics||Two 3" x 12" single-acting hydraulic cylinders complete with hoses & fittings.|
|Wing Flex||45° up, 20° Down while cutting.|
|Deck Material||1 - Piece, 10 gauge. (3.4 mm)|
|Side Skirt Material||1/4" plate (6 mm)|
Reversible & Replaceable: 2 straight skid shoes and 2 AR400 leading skid shoes.
Replaceable: 2 skid shoes
|Six Blades (2 per Carrier)||1/2" x 4" Heat Treated Free Swinging Alloy Steel with up lift.|
|Blade Bolt||Keyed with hardened flat washer & locknut.|
|Stump Jumper / Blade Holder||10 Gauge round dish shaped pan, reinforced with 1" x 4 1/2" blade mounting bar.|
|Deck Ring||Optional 3/8" formed and welded.|
|Front & Rear Guards||Optional single chain or double chain.|
|Input Driveline||ASAE Cat. 6 with constant velocity u-joint or Cat. 5 with conventional (non-cv) u-joint|
|Intermediate & Wing Drivelines||Cat. 4 with slip-clutch or optional Cat. 5 with slip-clutch|
|Tire Options||6" x 9 x 21" Laminated tires
29" x 9" Used aircraft tires without foam filling
27" x 7.75" Used aircraft tires with foam filling
|Number of Wheels||6 - Wheel option: 4 on transport axle and one on each wing axle.
8 - Wheel option: 4 on transport axle and two on each wing axle.
|Standard Transport Axle||Spring-cushioned on center transport axle.|
|Axle Fasteners||1 1/4" Greasable pins|
|Hubs||Cast iron five-bolt hubs with tapered roller bearings and 1 3/4" shafts.|
Join our Mailing List