Land Pride RC4610
Features
| Features | Benefits |
| Surpassed rugged industry standards |
All Land Pride Rotary Cutters have been designed and tested and meet rigorous voluntary testing procedures according to ISO 4254-13. |
| Factory assembled | Arrives for quick and easy set-up. Minimal time is wasted setting or prepping the unit. |
| 7 Year gearbox warranty | Shows confidence in gearbox integrity. (Years 6 & 7, parts only.) |
| Rugged heavy built gearboxes | Capable of handling heavy cutting applications. |
| Gearbox seal protection | Gearbox bottom seal protection for longer bearing life. |
| 2 3/8" Output gearbox shaft | Large output shaft handles shock loads better. |
| 2 Piece shield on wing gearbox | Driveline grease zerks are easier to access. |
| LED signal lights | LED lights are bright, long lasting, and resistant to vibration, unlike incandescent counterparts. |
| LP Performance Hitch | Reduces drawbar wear by keeping hitch level while going through ditches. |
| Low hitch weight on tractor drawbar | Ideal for smaller hp tractors by reducing the amount of weight on the drawbar. |
| Narrow A-frame hitch | Allows for a tighter turning radius. |
| Adjustable park jack angle | Park jack can be adjusted to be perpendicular to the ground. |
| Adjustable driveline hanger | Serves as a support rest for the driveline when the cutter is unhooked from the tractor. Assist operator when attaching driveline to tractor power take-off shaft. |
| Input driveline: Cat. 6 CV | Driveline is matched just right for capacity of tractor. Constant velocity (CV) U-joint allows for 80 degree turns without doing damage to the driveline. |
| Drivelines with slip-clutches: Cat. 5 intermediate Cat. 4 Wing |
Driveline is sized right for the intended cutting capacity. Slip-clutches will slip under load to minimize twist damage to driveline profiles. |
| Grease zerks on end caps of driveline cross journals |
Intermediate and wing driveline cross journals are easier to grease. |
| High Blade tip speed | Allows clean cutting of material. |
| 6" Blade overlap | Eliminates skipping during turns. |
| Good cutting capacity | Can cut brushy areas with saplings up to 3 1/2". |
| 12" Deck height | Handles heavy cutting, which reduces balling-up of cut material under the deck. |
| 3/16" Round stump jumper | Standard thick stump jumper material keeps damage to a minimum. |
| Smooth Top Design | Allows for easy cleaning of deck. |
| Deck sheet tops are 100% welded | Makes center deck and wing deck stronger. |
| 1/4" Sidewall thickness | Increased thickness reduces damage from objects being thrown into deck sidewalls. |
| Beveled skid shoe on wing | Reduces gouging the ground when turning. |
| Hinged wing section | Allows cutter to follow terrain. Ideal for rough ground where hillsides, ditches, and hollows can cause uneven cutting. |
| 1" Solid hinge rods | Larger diameter hinge rod gives greater strength to the cutter from front to rear, and in the hinge area itself. |
| Wing transport lock | Transport lock will hold the wing in the folded position in the event of hydraulic loss. |
| Enclosed dual leveling rods | Cutter pulls equally on the rear axle while traveling over rough terrain. |
| 5-Bolt hubs on trailing arms | 5-Bolt hubs makes the wheel assembly more durable and longer lasting. |
| Drain holes in wheel rims | Allows water to drain from wheel(s) mounted on folded-up wing. Helps prevent paint deterioration and rusting to the wheel rims. |
| Spring-cushioned trailing arms | Provides independent suspension, cushions loads on cutter and tractor drawbar. |
| Replaceable wheel spindles | Wheel spindles can be replaced when damaged without replacing entire axle assembly. |
| 7/8" Leveling rods | Large diameter leveling rods provide superior supporting strength over rough terrain. |
| Wheel options | Laminated tires: Eliminates flats. Air filled tires: Give better cushion while transporting. Foam-filled tires: Give better cushion while transporting and can’t go flat. |
| LP Performance Hitch option | Great for uneven terrain, reduces drawbar wear. Hitch pivots freely up and down and pivots about the tractor drawbar. |
| Bar-tite hitch option | Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear. |
| Deck ring option | Keeps blades from damaging the deck. |
Specifications
| Specifications & Capacities | RC4610 |
| Tractor horsepower | 50 - 200 hp |
| Gearbox horsepower | 540 rpm or 1000 rpm 250 hp divider 210 hp center & wing |
| Gearbox lubrication | Gear Lube 80-90W EP |
| Gearbox oil capacity | Splitter: 5.5 pints; Center deck & Wing: 10 pints |
| Cutting capacity | 3 1/2" |
| Machine weight Total weight Tongue weight |
4868 lbs. Includes 5 Laminated tires, single chains, deck rings, and LP Performance Hitch. 1920 lbs. |
| Blade tip speed At 540 rpm At 1000 rpm |
Center Blades = 16,300 FPM & Wing Blades = 16,300 FPM Center Blades = 16,288 FPM & Wing Blades = 16,000 FPM |
| Hitch types | Optional Self-Leveling Clevis Hitch, LP Performance Hitch, Bar-Tite Hitch, Pintle Hitch, or Ball Hitch |
| Hitch jack | Standard (7,000 lbs.) |
| Cutting width Overall width Minimum transport width |
10'-0" 11'-7 3/4" 7'-7 3/4" |
| Overall length | 16'-6" (Shorter if deck is raised fully up) |
| Deck height | 12" |
| Cutting height | 2" - 14" |
| Lift hydraulics | 3" x 8" hydraulic cylinder, hoses, fittings & stroke control spacers |
| Wing Flex | 45o up, 20o down while cutting. |
| Wing hydraulics | 3" x 12" hydraulic cylinder, hoses & fittings |
| Wing transport protection | Wing transport lock |
| Deck material | 10 gauge |
| Side skirt material | 1/4" plate |
| Skid shoes Wing deck Center deck |
1 Replaceable shoe 2 Replaceable shoes |
| Signal lights 7 Pin connector |
LED (light-emitting diode) SAE J560 pin configuration |
| Blades - 4 (2 per carrier) | 1/2" x 5" Heat Treated Free Swinging Alloy Steel with Uplift |
| Blade overlap | 6" |
| Blade bolt | Keyed with hardened flat washer & locknut |
| Stump jumper / Blade holder | 3/16" Thick round dish shaped pan, reinforced with 1" x 5" blade bar |
| Deck ring | Optional 3/8" x 4 1/2" |
| Front & rear guards | Optional single row chain or dual row chain |
| Input driveline 540 & 1000 power take-off speed | ASAE Cat. 6 with constant velocity u-joint |
| Intermediate driveline | Standard - Category 5 with Slip-Clutch |
| Wing driveline | Standard - Category 4 with Slip-Clutch or optional Category 5 with Slip-Clutch |
| Wheel options | 6" x 21" Laminated tires 25.5" new tire with or without foam fill 29" x 16 ply used aircraft tires without foam filling |
| Number of wheels | 5 - Wheel option: 4 on transport axle and one on wing axle 6- Wheel option: 4 on transport axle and two on wing axle |
| Transport axle | Spring-cushioned on trailing arms |
| Hubs | Cast iron five-bolt hubs with tapered roller bearings and 1 3/4" shafts. |
Join our Mailing List