Land Pride RCM5610

Features
Features | Benefits |
Surpassed rugged industry standards |
All Land Pride Cutters have been designed and tested and meet rigorous voluntary testing procedures. |
Factory assembled | Saves customer set-up time and money. |
7 Year gearbox warranty* | Shows confidence in gearbox integrity. |
250 HP Divider gearbox 210 HP center & wing gearboxes |
A rugged heavy built gearboxes capable of handling heavy cutting applications. |
Gearbox Seal Protection | Gearbox bottom seal protection for longer bearing life. |
2 3/8" Output gearbox shaft | Large output shaft handles shock loads better. |
Input driveline: Cat. 6 CV or Cat. 5 Conventional |
Holds up to shock loads and harsh mowing conditions. Constant velocity (CV) U-joint allows for 80 degree turns without doing damage to the driveline. |
Cat. 5 intermediate & Cat. 4 wing drivelines with slip-clutches |
Driveline is sized right for the intended cutting capacity. Slip-clutch will slip under load instead of twisting the driveline. |
Easy Greasable drivelines | Drivelines have access holes for greasing the U-joints and to grease the inner profiles. |
2 or 4 Plate slip-clutch | Protects drivelines and gearboxes by slipping clutches rather than twisting the driveline when impacts are encountered. |
High blade tip speed (See Specifications for actual FPM) |
Allows clean cutting of material and even distribution. |
6" Blade overlap | Eliminates skipping during turns. |
High cutting capacity 56 Series 66 Series |
Can cut brushy areas with saplings up to 4". Can cut brushy areas with saplings up to 4 1/2". |
12" Deck height | Handles heavy cutting, which reduces balling-up of cut material under the deck. |
3/16" Stump jumper backed with a 1" thick mounting bar |
Heavy round stump jumper with bottom gearbox seal protector. Can hold up to tough conditions. |
10 Gauge smooth deck top | Reduces accumulation of debris and is easier and faster to clean. |
7 Gauge smooth deck bottom | Heavy deck design holds up to harsh conditions. No bottom obstructions. |
Replaceable 1/4" side skirt | Reduces debris piercing possibilities. Can be replaced if damaged. |
Self-leveling hitch | Reduces drawbar wear by keeping hitch level while going through ditches. |
Hinged wing section | Allows cutter to follow terrain. Ideal for rough ground where hillsides, ditches, and hollows can cause uneven cutting. |
1" Solid hinge rods | Larger diameter hinge rod gives greater strength to the cutter from front to rear, and in the hinge area itself. |
Wing transport lock pin | Holds transport wing in the folded-up position in case of hydraulic pressure loss. |
Enclosed front to rear dual leveling rods |
Dual leveling rods enable the cutter to pull equally on the rear axle during travel over rough terrain. Many competitors only use one leveling rod. |
5-Bolt hubs | 5-Bolt hubs makes the wheel assembly more durable and longer lasting. |
Drain holes in wheel rims | Allows water to drain from wheels mounted on folded-up wing. Helps prevent paint deterioration and rusting to the wheel rims. |
Spring-cushioned trailing arms | Provides independent suspension, cushions loads on drawbar. |
Replaceable wheel spindles | Wheel spindles can be replaced when damaged without replacing the entire axle. Simply remove one bolt to replace damaged spindle. |
Pre-cut chamber | Allows grass and vegetation to stand back up prior to cutting for a more complete cut. |
Reinforced leading edge | Front of deck can withstand heavy brush and saplings. |
Collapsible leveling rods | Prevents damage and failure to leveling rods. |
1" Leveling rods | Large diameter leveling rods provide superior supporting strength over rough terrain. |
Double swivel hitch | Great for uneven terrain, reduces drawbar wear. |
Bar-tite hitch | Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear. |
Wheel options | Laminated tires: Eliminates flats. Airplane tires without foam filling: Give better cushion while transporting. Airplane tires with foam filling: Give better cushion while transporting and can’t go flat. |
Deck rings (optional) | 1/2" x 3" full welded deck ring keeps blades from damaging the deck. |
Specifications
Join our Mailing List